Braking distance refers to the distance a vehicle will travel from the point when its brakes are fully applied to when it comes to a complete stop. It is primarily affected by the original speed of the vehicle and the coefficient of friction between the tires and the road surface, and negligibly by the tires' rolling resistance and vehicle's air drag. The type of brake system in use only affects trucks and large mass vehicles, which cannot supply enough force to match the static frictional force.
The braking distance is one of two principal components of the total stopping distance. The other component is the reaction distance, which is the product of the speed and the perception-reaction time of the driver/rider. A perception-reaction time of 1.5 seconds, and a coefficient of kinetic friction of 0.7 are standard for the purpose of determining a bare baseline for accident reconstruction and judicial notice; most people can stop slightly sooner under ideal conditions.
Braking distance is not to be confused with stopping sight distance. The latter is a road alignment visibility standard that provides motorists driving at or below the design speed an assured clear distance ahead (ACDA) which exceeds a safety factor distance that would be required by a slightly or nearly negligent driver to stop under a worst likely case scenario: typically slippery conditions (deceleration 0.35g) and a slow responding driver (2.5 seconds). Because the stopping sight distance far exceeds the actual stopping distance under most conditions, an otherwise capable driver who uses the full stopping sight distance, which results in injury, may be negligent for not stopping sooner.
Maps, Directions, and Place Reviews
Derivation
Energy equation
The theoretical braking distance can be found by determining the work required to dissipate the vehicle's kinetic energy.
The kinetic energy E is given by the formula:
where m is the vehicle's mass and v is the speed at the start of braking.
The work W done by braking is given by:
where ? is the coefficient of friction between the road surface and the tires, g is the gravity of Earth, and d is the distance travelled.
The braking distance (which is commonly measured as the skid length) given an initial driving speed v is then found by putting W = E, from which it follows that
The maximum speed given an available braking distance d is given by:
Newton's Law and Equation of Motion
From Newton's second law:
For a level surface, the frictional force resulting from coefficient of friction is:
Equating the two yields the deceleration:
The form of the formulas for constant acceleration is:
Setting and then substituting into the equation yields the braking distance:
Total stopping distance
The total stopping distance is the sum of the perception-reaction distance and the braking distance.
A common baseline value of is used in stopping distance charts. These values incorporate the ability of the vast majority of drivers under normal road conditions. However, a keen and alert driver may have perception-reaction times well below 1 second, and a modern car with computerized anti-skid brakes may have a friction coeficient of 0.9--or even far exceed 1.0 with sticky tires.
Experts historically used a reaction time of 0.75 seconds, but now incorporate perception resulting in an average perception-reaction time of: 1 second for population as an average; occasionally a two-second rule to simulate the elderly or neophyte; or even a 2.5 second reaction time--to specifically accommodate very elderly, debilitated, intoxicated, or distracted drivers. The coefficient of friction may be 0.25 or lower on wet or frozen asphalt, and anti-skid brakes and season specific performance tires may somewhat compensate for driver error and conditions. In legal contexts, conservative values suggestive of greater minimum stopping distances are often used as to be sure to exceed the pertinent legal burden of proof, with care not to go as far as to condone negligence. Thus the reaction time chosen can be related to the burden's corresponding population percentile; generally a reaction time of 1 second is as a preponderance more probable than not, 1.5 seconds is clear and convincing, and 2.5 seconds is beyond reasonable doubt. The same principle applies to the friction coefficient values.
Actual total stopping distance
The actual total stopping distance may differ from the baseline value when the road or tire conditions are substantially different from the baseline conditions or when the driver's cognitive function is superior or deficient. To determine actual total stopping distance, one would typically empirically obtain the coefficient of friction between the tire material and the exact road spot under the same road conditions and temperature. They would also measure the person's perception and reaction times. A driver who has innate reflexes, and thus braking distances, that are far below the safety margins provided in the road design or expected by other users, may not be safe to drive. Most old roads were not engineered with the deficient driver in mind, and often used a defunct 3/4 second reaction time standard. There have been recent road standard changes to make modern roadways more accessible to an increasingly aging population of drivers.
Source of the article : Wikipedia
EmoticonEmoticon